California's Wildland-Urban Interface Code Information
Chapter 7A Building Code Language
- CA Building Code Chapter 7A (January 2009 Supplement)
- CA Fire Code Chapters 47
- CA Building Code Testing Standards
- 2010 Title 24 California regulations
Fire Safe Regulations
- How to get code questions answered
- Effective Dates of Code
- Information Bulletins
- Reference Materials
Protecting a building from wildfire takes a two-pronged approach:
- Remove flammable materials from around the building
- Construct the building of fire resistant material
The law requires that homeowners do fuel modification to 100 feet (or the property line) around their buildings to create a defensible space for firefighters and to protect their homes from wildfires.
New building codes will protect buildings from being ignited by flying embers which can travel as much as a mile away from the wildfire. The following ignition-resistant standards are designed to prevent embers from igniting a building:
Building Materials Listings for Wildland Urban Interface Building Materials
The Office of the State Fire Marshal's (SFM) Building Materials Listing Program (BML) was originally created to mandate that all fire alarm systems and fire alarm devices be approved and listed by the State Fire Marshal prior to sale or marketing within the state. The program later was expanded to include many other materials such as: roof coverings, fire resistive wall and ceiling-floor assemblies, wall finish materials, fire and non-fire related hardware, insulating products, fire doors, fire dampers, electrical appliances and devices. Each product approval and listing is based upon an evaluation of test results that include an analysis of required product performance and reliability features. All manufacturers that want to list products in California must have those products tested and labeled by a SFM accredited laboratory. If a product does not qualify for listing but meets the standard of the “Materials and Construction Methods for Exterior Wildfire Exposure,” Chapter 7A of the California Building Code will be listed in the WUI Product Handbook.
WUI Building Materials Testing Standards
- Testing Standards CA SFM 12.7A-1, Exterior Wall Siding and Sheathing
- Testing Standards CA SFM 12.7A-2, Exterior Windows
- Testing Standards CA SFM 12.7A-3, Under Eaves
- Testing Standards CA SFM 12.7A-4, Decking
- State Fire Marshal Building Materials Listing Web Page
The new building standard for the Fire Hazard Severity Zones will be enforced by the Building Official as projects go through the plan checking process. To best assist them in determining if a product meets the code requirements, the State Fire Marshal's BML Program is accepting applications for materials that meet the new code. These materials will be listed on the SFM BML website and the Wildland Urban Interface Building Codes page of the Wildland Hazards and Building Codes website section. The SFM listing service provides building authorities, architectural and engineering communities, contractors, and the fire service with a reliable and readily available source of information.
Since the materials under Wildland Urban Interface Building Codes (except wood shakes and shingles) are not required by law to be listed by the SFM, the listing for these products are strictly voluntary. Materials not listed by the SFM may still qualify for use provided they met all the requirements under Chapter 7A. If not listed on the SFM site, all documentation and testing certificates showing compliance must be submitted to the building official having jurisdiction for final approval.Effective Dates of Code:
On September 20, 2007 the Building Standards Commission approved the Office of the State Fire Marshal’s emergency regulations amending the California Code of Regulations (CCR), Title 24, Part 2, known as the 2007 California Building Code (CBC).
“701A.3.2 New Buildings Located in Any Fire Hazard Severity Zone.New buildings located in any Fire Hazard Severity Zone within State Responsibility Areas, any Local Agency Very-High Fire Hazard Severity Zone, or any Wildland-Urban Interface Fire Area designated by the enforcing agency for which an application for a building permit is submitted on or after January 1, 2008, shall comply with all sections of this chapter. New buildings located in any Fire Hazard Severity Zone shall comply with one of the following:
1. State Responsibility Areas.
New buildings located in any Fire Hazard Severity Zone within State Responsibility Areas, for which an application for a building permit is submitted on or after January 1, 2008, shall comply with all sections of this chapter.
2. Local Agency Very-High Fire Hazard Severity Zone.
New buildings located in any Local Agency Very-High Fire Hazard Severity Zone for which an application for a building permit is submitted on or after July 1, 2008, shall comply with all sections of this chapter.
3. Wildland-Urban Interface Fire Area designated by the enforcing agency.
New buildings located in any Wildland-Urban Interface Fire Area designated by the enforcing agency for which an application for a building permit is submitted on or after January 1, 2008, shall comply with all sections of this chapter.
Project specific questions should be addressed by the agency having jurisdiction of the project. They may have more restrictive requirements in local ordinances.
- Revised Effective Date of Wildland-Urban Interface Building Standards in Local Responsibility Areas (61K PDF)
- Enforcement of Building Code (36K PDF)
- Plan Review Bulletin (29K PDF)
New Building Standards have been adopted for areas within local jurisdiction Very High Fire Hazard Severity Zones and in the State Responsibility Areas (SRA). Phase I of the standards are already in effect. Phase II standards will go into effect January 1, 2008.
- Nine Point Criteria Analysis, Phase I
- Nine Point Criteria Analysis, Phase II
- Building Code Interpretations